Saturday, April 21, 2018

Replacing our RV Carpet–Part Two…

IMG_20180414_093628

Continuing the blog about our carpet installation, pulling up the carpet in the cockpit area was tedious since there were more cuts and thus more staples. With patience I eventually freed the old carpet. Interestingly there was only a little carpet padding as most of the area had a large rubber mat which I assume was designed to decrease engine noise and insulate from engine heat. For the cockpit area we chose a lower piled carpet and as I pulled the old carpet out I those pieces as a template to cut the new carpet. Another 100 stales into the floor and the cockpit was nearly done.

I said nearly since there is a hatch in our cockpit for access to our front engine diesel. This is also carpeted and removing the old carpet was a bit harder since this piece had been not only stapled but glued on using Weldwood contact cement. Using a pair of pliers I slowly pulled on an edge of carpet using the carpet knife to cut the glue away. It took a while but it was done. I also used contact adhesive to glue on the new carpet adding only staples all along the edges. Viola – Cockpit done!

IMG_20180414_093532IMG_20180420_102947

Next up was the steps in the entrance area. The sides are where the carpet was and man oh man were they stapled in and glued as well… After pulling out seemingly endless staples I was able to use the pliers and carpet knife to remove the old carpet. Using the old carpet as a template, new pieces of carpet were cut and glued in place. A few additional staples and the step area was done.

All that was left was the large living room/dining room slide. Since it was on a slide the old carpet was fairly easy to remove. No glue and only staples were used so I was able to manhandle off the floor. There was no carpet padding under the slide and I didn’t add any either. Again using the old carpet as a template I cut the slide out carpet which was the lusher, higher piled carpet we also used in the bedroom.

IMG_20180420_102953IMG_20180414_093540

Once it was cut we took it over to Carpet Handlers in Bryan Texas to have the edge of it bound. They charged $3 per running foot to bind it and it took about 4 days to get it back. It needed to be bound as the edge must hang off over the slide to cover up the slide gap. If it wasn’t bound it would have continued to fray and shed carpet fibers.

Final installation of this slide carpet was a snap. I did forget to mention in the removal of the old carpet I also had to take out the sofa which was held down by four bolts. It was easy to remove. Then there were four bolts holding down the seat belts for the sofa which were also easy to remove. I made sure to label where each seat belt went to make it easier to put them back in their rightful spot.

IMG_20180420_103011IMG_20180414_093701

With the new slide carpet bound all I needed to do was measure and mark the place where all the bolts would come through the carpet and cut little slits so they would come through it. With them in place I stapled along the edges near the bolts so I could locate where the couch bolts would go through the carpet. I marked the spots with scotch tape so I could align the couch properly. Placing the couch near the tape and using an ice pick to locate the holes which hold the couch in place I was able to sink the screws into the floor. With the seat belts and couch back to where they belonged I continued stapling the carpet as I used the knee kicker to keep it stretched.

To finish the job I needed to use a coping saw to remove 1/4 of an inch of the trim that the bound carpet would slide under since the new carpet was a bit thicker. With the trim cut I finished the stapling and put everything back in its place.

Now that all of our flooring has been replaced the RV is ready for many more years of travel on the Road of Retirement…

NOTE: We are still in College Station, Texas for the month of April…

3 comments:

  1. Nic to get all the flooring done, sure doe make a great improvement , we love our new flooring.

    ReplyDelete
  2. Great job!!! I bet it looks as good as new!! 🙂
    We are actually looking at purchasing an Allegro Bay 37 QDB in Columbia Tennessee. Yes, the Oliver is awesome but can and does get small for full-timing!! It’s the FRED!! I believe that is your coach right? Any words of wisdom??? The owners have done a bunch of upgrades such as MCD blinds throughout, residential refrigerator, washer/dryer and some other things! What we perceive as a fair price!!

    ReplyDelete
    Replies
    1. Yes, ours is also a 37QDB and we love it. There was a recall on the 4 door fridge so make sure that was done and ask if the roof rails have ever been replaced as they were an issue with this model. Otherwise we have only had mostly normal wear and tear... ask me anything else and I will be glad to help you.

      Delete